How to Make a Wood Plate Rack

How to Make a Wood Plate Rack

An very wellplate rack allows you to show plates and may be made in an afternoon for the value of a few dowels and some glue. now not counting the time required to cut the portions or to permit the finish to dry, this plate rack may be assembled and installed in a kitchen cabinet in about 1/2-hour. commands are for a widespread wooden cupboard that is 24 inches extensive.

dispose of the doorways from the cabinet wherein you need to put in your o.k.plate rack. Set them apart.

cut the square dowels to healthy the inside width of the cabinet, if important. cut dowel rods (the spherical ones) to 11 1/4 inches. Sand all the dowels clean with nice grit sandpaper. You need a clean finish in your timber rack, so take a while on this step.

Lay the scrap plywood for your paintings surface. degree and mark the position of the dowel rods at the square dowels. starting on the left edges of the rectangular dowels, vicinity marks at 1/2 inch, 2 half of inches and each two inches after that (four half inches, 6 1/2 inches and so forth). The ultimate gap can be larger than the others, to make room for a platter. go away half inch gaps on the ends to permit for air circulation. if you want to position different dishes to your plate rack, including serving dishes or extra platters, and that they require more space than 2 inches, make more than one of the areas on the cease wider than the others. you can cause them to all of the identical larger length if you desire, however remember the fact that you'll have fewer slots to your plate rack in case you do. Fewer however wider slots let you display plates higher, however.

Drill holes for the o.k.plate rack uprights. Drill the holes into the rectangular dowels. if you don't have get right of entry to to a drill press, you may still make this rack, it's going to just take a couple of minutes longer. Wrap protecting tape round a three/8 inch drill bit to mark a drilling intensity of 3/eight inch. put the drill bit right into a cordless drill, middle the bit exactly at the marks, preserve the drill perfectly level, and thoroughly drill the holes.

area one drop of timber glue into each hollow in one of the rectangular dowels. most effective do the holes in one square dowel at a time. After setting glue inside the remaining hole, slip a dowel rod into the first hollow. Rotate the dowel rod to distribute the glue calmly around the inner of the hollow. Repeat for each hollow in that rectangular dowel.

placed drops of glue into the holes within the 2d square dowel just as you did the first one and in shape it to the uncovered ends of the dowel rods. pick out up the "ladder" you simply made, with a rectangular dowel in each hand, and press them firmly closer to each other till the dowels have slid into the holes as a long way as they may move. this is known as seating the dowels.

Repeat steps 5 and 6 to build the second "ladder." One "ladder" will cross into the lower back of the cupboard, and the opposite will move into the front fringe of the cabinet, and the plates and platters will slide into the rack and be held in region by way of each the back and front rods. some people best vicinity a "ladder" in the the front of the cupboard, but this is not encouraged due to the fact the plates and platters will no longer be held securely and can smash in opposition to every other.

finish plate rack ladders as desired to seal the wooden. Use a paintbrush and timber stain, if desired. whether you operate wood stain, proceed with polyurethane end. observe at the least three coats of polyurethane, bearing in mind drying time referred to as for among coats as directed by the manufacturer.

set up your very wellplate rack. vicinity one "ladder" about 3 inches from the lower back of the cabinet, and just to the right facet of the leftmost dowel rod, drive a 1-inch lengthy screw up via the rectangular dowel and into the cupboard itself. Countersink the screw a chunk, however take care no longer to force screws all the manner through the cabinet. simply to the left of the rightmost dowel rod, drive some other screw up via the square dowel and into the cabinet. pressure a screw down into the bottom square dowel within the identical places, just within the first and remaining dowel rods, and into the cabinet.

location the front "ladder" flush against the front edge of the cupboard. relaxed it with 4 screws, just as you did with the "ladder" this is inside the returned of the cabinet.

Source: here

Leave a comment