How to Install Pex Tubing for Water Lines

How to Install Pex Tubing for Water Lines

PEX move-connected polyethylene tubing is reasonable and clean to handle; consequently, many professional plumbers and DIY domestic developers have switched to PEX in favor of copper tubing. PEX is straightforward to install, much less liable to freeze damage, and its water-hammer resistant. PEX is supplied in one hundred m spools, so it is able to be used for long piping runs and turn ninety-degree corners. this means that fewer in-line couplings and right-attitude elbows are required. further, this cloth may be easily linked to copper and CPVC tubing with out the usage of adhesives, solder or corrosive flux.

connect PEX to a extensive kind of crimp-style adapters with copper crimp rings and a PEX crimping device. vicinity a copper crimp ring over the squarely cut stop of a period of PEX, insert a brass or plastic crimp-style adapter into the tube and function the jaws of the clamping tool over the copper crimp ring. Press the handles of the clamping tool together.

check the joint with the go/no-cross gauge supplied; if the ring doesnt suit into the no-go slot, however suits into the move slot, the joint is watertight to two hundred lbs. in line with rectangular inch of pressure.

clamp PEX tubing to crimp-fashion adapters with widespread stainless steel clamp earrings if this is the desired method. reduce the cease of the PEX off at ninety stages with a PEX tubing cutter akin to a pair of pruning shears.

location a stainless-steel clamp ring over the stop and insert the ribbed pipe adapter. function the clamp ring at the middle of the ribbed shaft. region the jaws of general ratcheted clamping device over the lug at the crimp ring and squeeze the handles collectively several times until they wont flow any in addition.

Mark the cut line at the copper tube with a pencil. location the pipe between the rollers and slicing blade of a hand held tubing cutter. Tighten the knurled cutting wheel knob. Rotate the cutter over the pipe three or four turns till there is no extra resistance. maintain on tightening the knurled knob and rotating the device around the pipe till it's far severed.

cut the quit of the PEX off rectangular with a PEX tubing cutter. Mark a line 1 inch from the end on every piece of pipe with a felt-tipped pen.

Insert the end of the copper tube into a unique PEX press-fit coupling. Press the tube into the coupling until the marked line on the facet of the tube reaches the lip of the coupling; you will experience the clamping tooth inside the coupling click into location. Repeat with the PEX aspect of the coupling to finish a watertight joint capable of resisting 200 psi.

connect PEX to manifolds, boilers and hot water heaters with PEX compression fittings. these fittings include three parts: an R20 or R25 threaded nut, a ferule and a tubing insert. Slide the threaded nut onto the tubing with the threads dealing with the give up, region the ferule over the tubing and push the insert all the manner into the tubing.

Thread the brass connector nut onto a manifold or different plumbing gadgets inlet or outlet port, whichever is applicable. Tighten the hex connector nut with an adjustable wrench, but do now not overtighten.

take a look at the relationship for leaks once water pressure is restored. in case you hit upon a moderate leak, tighten the brass hex nut 1 / 4 turn and recheck; this have to stop the leak. Repeat with some other sector flip in case you nonetheless come across a leak, but don't move any in addition; overtightening will harm the rubber washer inside the compression fitting.

shut off the water deliver and put off the leaking coupling. easy up the mating surface at the appliance with a strip of four hundred-grit emery paper. Reconnect the coupling and retest,

connect 1/2 inch PEX-a tubing to three/4 inch PEX tubing with a ramification coupling as follows: area a seasoned-PEX ring across the cease of your half inch PEX-a tubing, sticking out 1/eight inch over the cease.

Screw the best size head onto a Wirsbo expander device. Insert the tapered head of the expander tool into the half of inch PEX tubing. carry the handles together to amplify the tube. preserve bringing the handles collectively five to fifteen times while rotating the tube.

put off the device and quickly insert a half of inch to a few/four inch pro-PEX fitting into the pipe. The half of inch PEX-a tubing will then shy away to its original size to complete the watertight connection.

Source: here

Leave a comment