DIY Faux Acrylic Photo Frames

DIY Faux Acrylic Photo Frames

Lucite (or generically known as acrylic) is a fantastic, current medium used for plenty objects in home dcor these days from espresso tables to cribs to utensils. The clear plastic-y cloth is visually light-weight, making its presence inherently understated but additionally chic. Lucite portions can be high priced, however, so if you like the appearance but dont have the coins to position closer to Lucite, that is a fantastic DIY concept for you! image, or artwork, double frames with brass fasteners mimic the luxe look without breaking the bank.

This mission isnt tough, in step with se, however it does take a few endurance and the proper technique.

mission Prep: decide at the picture or piece of art you want to frame, then measure it. (Tip: This educational suggests two 24 rectangular snap shots revealed out as engineer prints at Staples. At approximately $four apiece, that is a fabulously inexpensive manner to customise your piece.)

At your local hardware shop, in the plastic sheeting segment, youll discover various sizes of plastic sheeting. pick out the piece(s) that most intently matches four larger than the photo youre framing, then have them cut to size. (as an instance, the pictures used here are 24 rectangular, so the plastic sheeting I chose to have cut become 28x30, I think.) Youll want identical portions consistent with photograph body.

begin through measuring and staining 1-half of in from each nook on one of the acrylic sheets. Make these marks at the removable protective plastic covers in your acrylic sheets.

also mark 1-half in on the halfway point on every facet.

cautiously stack up your acrylic sheets, being unique in lining up the corners. (Tip: 4 sheets are proven right here; do now not stack extra than four.) maintain the marked acrylic sheet on top.

Taking care that the corners are lined up exactly, clamp the nook close to the first mark.

Aligning corners as you move and adjusting as vital, clamp the relaxation of the corners. Tip: clamp diagonal corners first and 2nd, then the opposite two diagonal corners third and last. This facilitates to preserve the acrylic sheets from any transferring.

several tutorials advise melting holes in the acrylic sheets in your brass fasteners; others recommend drilling. i've accomplished both, and that i endorse a aggregate of the 2 soften a touch, then drill. To do this, tightly grasp a large nail with pliers and maintain it over a heat source, which include a candle flame. let the tip get warm.

quickly but very carefully, push the hot nail tip into the clamped acrylic sheets at a factor youve marked. Push down as a ways as you want, however dont worry approximately going all the manner via. The idea here is to offer your drill a terrific start line to drill through the opposite layers.

the use of a drill bit that is the dimensions of your brass screws (or ever so slightly larger), slowly start drilling at the melting factor inside the acrylic sheet. (The melting point facilitates the drill bit stay in vicinity at the smooth acrylic floor.) You need to apply effort however now not pressure, due to the fact the acrylic sheets will crack if you try to pass too difficult and too fast. Repeat this soften-and-drill technique for all 8 holes. Be cautious with the drilling so there aren't any cracks!

Pull one side of protective plastic off one acrylic sheet. This exposed floor may be internal your body. go away the protective plastic on the alternative side of this sheet for now.

using needlenose pliers, gently easy up the holes of any melted or caught acrylic bits.

Wipe off all acrylic shards out of your sheet. don't forget, this surface can be sandwiched, so you wont be capable of get to it later.

middle your photograph at the acrylic sheet.

Take care to hold your arms and the acrylic sheet surface clean and dry as youre doing this.

Now pull off each facets of the protective plastic on the second one acrylic sheet. remove shards with your needlenose pliers and wipe the inner floor with a clean, dry cloth. Align the holes of this acrylic sheet together with your first one, and lay it on top, being cautious not to shift your now-sandwiched photograph.

Take a brass screw and push or screw it into the primary hollow.

Screw the nut onto the screw, securing the 2 acrylic sheets collectively.

Youll need to tighten the nut to match snugly (use a screwdriver and pliers) however DO no longer OVERTIGHTEN. an excessive amount of strain may additionally reason your acrylic sheet(s) to crack. do that for all 8 of the holes, but dont tighten the two side holes. those may be on your putting wire/line.

I selected to use fishing line because of its transparency; a small quantity of your putting line might be visible on both facet of your photo. to start, tie a 1 loop on the end of your fishing line. Hook this onto one of the facet screws, between the nut and the back acrylic sheet.

Wrap the fishing line to and fro among the two side screws approximately ten instances. Youll need to maintain the road taut however dont pull it too tight, or your body will bow and bend while you visit dangle it.

After the tenth (or so) pass, tie every other loop in the end of your fishing line and hook it onto the screw underneath the nut.

carefully tighten the two aspect nuts now, if you need to. This have to cinch down and comfortable your fishing line.

Congratulations! Youre prepared to grasp!

Dont you just love the crisp, present day sense of a two-planed frame? The floating effect is so on factor.

And the small brass info really supply it a cutting-edge vibe.

we hope you enjoy making your personal DIY fake acylicphoto frames! the sort of expert-looking way to border huge artwork or pix, and it adds a lot personality to a space.

Source: here

Leave a comment